Venkovní CPE zařízení 2.4GHz 300Mbit/s 12dBi CPE220 Vestavěná 12dBi 2x2 směrová MIMO anténa s dvojitou polarizací Nastavitelný výkon vysílání od 0 do 30dBm/1000mWOptimalizace na úrovni systému pro více než 13km dosah bezdrátového přenosu Technologie TP-LINK Pharos MAXtream TDMA (Time-Division-Multiple-Access) zlepšuje výkon zařízení co se týče propustnosti, kapacity a latence, ideální pro aplikace PTMP Centralizovaný sytém ovládání - řízení Pharos Provozní režimy AP / Client / Bridge / Repeater / AP Router / AP Client Router (WISP) Pasivní PoE adaptér podporuje napájení přes Ethernet až na 60 metrů a umožňuje vzdálené resetování zařízení HARDWARE FEATURES Processor Qualcomm Atheros 560MHz CPU, MIPS 74Kc Memory 64MB DDR2 RAM, 8MB Flash Interface 1 10/100Mbps Shielded Ethernet Port (LAN0,Passive PoE in) 1 10/100Mbps Shielded Ethernet Port (LAN1, Passive PoE Passthrough) 1 Grounding Terminal 1 Reset Button Power Supply Passive Power over Ethernet via LAN0 (+4,5pins; -7,8pins) Voltage range: 16-27VDC Power Consumption 10.8 Watts Max Note: When deployed using Passive PoE, the power drawn from the power source will be higher by some amount depending on the length of the connecting cable. Dimensions ( W x D x H ) 11×3.1×2.1 inch (276×79×60 mm) Antenna Type Built-in 12dBi 2x2 Dual-polarized Directional Antenna Beam Width: 60° (H-Plane) / 30° (E-Plane) Note: For more details, please refer to datasheet Protection 15KV ESD Protection 6KV Lightning Protection Enclosure Outdoor ASA stabilized plastic material IPX5 waterproof Certification WIRELESS FEATURES Wireless Standards IEEE 802.11b/g/n (with Pharos MAXtream disabled) Proprietary Protocol TDMA Mode (with Pharos MAXtream enabled) Wireless Speeds Up to 300Mbps (40MHz,Dynamic) Up to 144.4Mbps (20MHz,Dynamic) Up to 72.2Mbps (10MHz,Dynamic) Up to 36.1Mbps (5MHz,Dynamic) Frequency 2.4~2.483GHz Note: Available operating frequency may vary depending on the limitations of the countries or regions in which the device is used. Transmission Power 30dBm/1000mw (Adjustable power by 1dBm) Note: Maximum transmission power may vary across different channels depending on the limitations of the countries or regions in which the device is used. SOFTWARE FEATURES Wireless Configurations Pharos MAXtream TDMA Technology 802.11b/g/n Modes Selectable Channel Width: 5/10/20/40MHz Automatic Channel Selection Transmission Power Control Dynamic Frequency Selection (DFS) WDS Enable/Disable Security: WPA/WPA2, WPA-PSK/WPA2-PSK (AES/TKIP) Encryption, 64/128/152-bit WEP Encryption SSID Broadcast Enable/Disable Multi-SSID with VLAN Tagging (AP mode only) Distance/ACK Timeout Setting Wireless MAC Address Filter Wireless Advanced: > Beacon Interval/RTS Threshold/Fragmentation >Threshold/DTIM Interval/AP Isolation/Short GI/Wi-Fi Multimedia 802.1Q – VLAN Tagging Management Discovery and Remote Management via Pharos Control application HTTP/HTTPS Web-based management System Log SNMP Agent(v2c) Ping Watch Dog Dynamic DDNS SSH Server System Tools Wireless Signal Quality Indicators: Signal Strength/Noise/Transmit CCQ/CPU/Memory Monitors: Throughput/Stations/Interfaces/ARP/Routes/WAN/DHCP Spectrum Analyzer Speed Test Ping Traceroute System-level Optimizations Optimized IGMP Snooping/Proxy for multicast applications Hardware watch dog POE ADAPTER FEATURES Dimensions(W x D x H) 110×57×33.5mm Interfaces 1 AC Jack with Earth Ground 1 10/100Mbps/1000Mbps Shielded Ethernet Port (Power + Data) 1 10/100Mbps/1000Mbps Shielded Ethernet Port (Data) Button Remote Reset Button Power Status LEDs 0~0.8A: Green 0.8A~1.0A: Red Input 100-240VAC, 50/60Hz Input Voltage 100VA~240VAC @ 50Hz~60Hz Input Current 0.8A Max @ 100VAC Output 24VDC, 1.0A Max +4, 5pins; -7, 8pins. (Support up to 60m Power over Ethernet) Output Voltage 24VDC(+4,5pins; -7,8pins) Efficiency >80% Certifications CE/FCC/UL/IC/GS/PSB/C-tick/SAA/S-Mark/KC-mark OTHERS Certification CE, FCC, RoHS, IPX5 Package Contents Outdoor Wireless CPE 24V 1A Passive PoE Adapter Pole Mounting Straps AC Power Cord Installation Guide System Requirements Microsoft Windows 98SE, NT, 2000, XP, Vista™ or Windows 10, Windows 8, Windows 7, MAC OS, NetWare, UNIX or Linux. Note: We recommend you to use one of following Web browsers for an improved user experience: Google Chrome, Safari, and Firefox. IE browsers are not recommended. Environment Operating Temperature: -30°C~70°C (-22?~158?) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~95% non-condensing

300Mbps Wireless N Ceiling Mount Access Point EAP115 V4 Bezplatný software Omada pro řízení ovladače umožňuje administrátorům snadno spravovat stovky EAP Podporuje napájení přes datovou síť (protokol 802.3af) PoE pro praktickou a cenově dostupnou instalaci Jednoduchá konstrukce umožňuje snadné upevnění na stěnu nebo strop Kaptivní portál poskytuje jeden z praktických způsobů autentizace hostů sítě Wi-Fi Autentizace hostů Wi-Fi sítě díky podpoře přihlášení přes Facebook a SMS pomáhá rozšířit vaše obchodní aktivity Zabezpečení Wi-Fi na podnikové úrovni pomáhá snížit bezpečnostní hrozby Multi-SSID umožňuje vytvořit několik bezdrátových sítí pro různé typy uživatelů Podporuje řízení VLAN pro větší možnosti správy sítě HARDWARE FEATURES Interface Fast Ethernet (RJ-45) Port *1(Support IEEE802.3af PoE) Button Reset Power Supply PoE or external 9VDC/0.6A power supply Power Consumption 2.8W Dimensions 7.5×6.8×1.2 in. (189.4×172.3×29.5mm) Antenna Type Internal 2* 4dBi Omni Mounting Ceiling /Wall Mounting (Kits included) WIRELESS FEATURES Wireless Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Frequency 2.4-2.4835GHz Signal Rate 11n: Up to 300Mbps(dynamic) 11g: Up to 54Mbps(dynamic) 11b: Up to 11Mbps(dynamic) Reception Sensitivity 300M: -71dBm@10% PER 150M: -75dBm@10% PER 54M: -78dBm@10% PER 11M: -93dBm@8% PER 6M: -92dBm@10% PER 1M: -96dBm@8% PER Wireless Functions Multiple SSIDs (Up to 8 SSIDs) Enable/Disable Wireless Radio Automatic Channel Assignment Transmit Power Control (Adjust Transmit Power on dBm) QoS(WMM) Rate Limit Reboot Schedule Wireless Schedule Wireless Statistics based on SSID/AP/Client Wireless Security Captive Portal Authentication Access Control Wireless MAC Address Filtering Wireless Isolation Between Clients SSID to VLAN Mapping Rogue AP Detection 802.1X Support 64/128/152-bit WEP / WPA / WPA2-Enterprise,WPA-PSK / WPA2-PSK Transmission Power CE: ?19dBm(EIRP) FCC: ?21dBm MANAGEMENT Omada Controller Software Yes Email Alerts Yes LED ON/OFF Control yes Management MAC Access Control Yes SNMP v1,v2c System Logging Local/Remote Syslog Local/Remote Syslog Telnet yes Web-based Management HTTP/HTTPS Management VLAN Yes OTHERS Certification CE, FCC, RoHS Package Contents 300Mbps Wireless N Ceiling Mount Access Point EAP115 Power Adapter Mounting Kits, Installation Guide System Requirements Microsoft Windows 10/8/7/Vista/XP Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

300Mbit/s bezdrátový venkovní N Access point EAP110-Outdoor Vytvořen pro venkovní realizace Wi-Fi Až 300Mbit/s rychlost Wi-Fi s technologií 2x2 MIMO Vysoký přenosový výkon a vysoký zisk antén poskytuje pokrytí s velkým rozsahem Pouzdro odolné povětrnostním vlivům, aby odolal hezkému i špatnému počasí Podpora pasivního PoE (Power over Ethernet) a snadno namontovatelné provedení umožňuje flexibilní rozmístění a pohodlnou instalaci Volně dostupný Auranet Controller Software umožňuje administrátorům snadné řízení stovek EAP Captive portál poskytuje pohodlnou metodu ověřování hostů Podporuje VLAN pro lepší správu sítě Facebook Wifi a SMS autorizace pomáhají podpořit vaše podnikání HARDWARE FEATURES Interface Fast Ethernet (RJ-45) Port *1(Support Passive PoE) Button Reset Power Supply 24V Passive PoE (+4,5pins; -7,8pins. PoE Adapter Included) Power Consumption 3.12 W Dimensions ( W x D x H ) 8.5 × 1.8 × 1.1 in. (216 × 46 × 27 mm) Antenna Type 2*3dBi External Omni waterproof Weatherproof Enclosure IP65 Mounting Pole / Wall Mounting (Kits included) WIRELESS FEATURES Wireless Standards IEEE 802.11n/g/b Frequency 2.4GHz Signal Rate 11n: Up to 300Mbps(dynamic) 11g: Up to 54Mbps(dynamic) 11b: Up to 11Mbps(dynamic) Transmit Power CE: ?20dBm (EIRP) FCC: ?22dBm Wireless Functions Multiple SSIDs(Up to 8 SSIDs) Enable/Disable Wireless Radio Automatic Channel Assignment Transmit Power Control (Adjust Transmit Power on dBm) QoS(WMM) Load Balance Rate Limit Reboot Schedule Wireless Schedule Wireless Statistics based on SSID/AP/Client Wireless Security Captive Portal Authentication Access Control Wireless Mac Address Filtering Wireless Isolation Between Clients SSID to VLAN Mapping Rogue AP Detection 802.1X Support 64/128/152-bit WEP / WPA / WPA2-Enterprise, WPA-PSK / WPA2-PSK MANAGEMENT Omada Cloud Access Yes Omada App Yes Omada Cloud Controller Yes Omada Controller Software Yes Email Alerts Yes LED ON/OFF Control Yes Management MAC Access Control Yes SNMP Yes System Logging Local/Remote Syslog Local/Remote Syslog SSH Yes Web-based Management HTTP/HTTPS L3 Management Yes Multi-site Management Yes Management VLAN Yes OTHERS Certification CE, FCC, RoHS Package Contents 300Mbps Wireless N Outdoor Access Point, EAP110-Outdoor Passive PoE Adapter Power Cord Mounting Kits Waterproof Rubber Insert Waterproof Antennas Installation Guide System Requirements Microsoft Windows XP, Vista, Windows 7, Windows 8, Windows10 Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

TL-WN822N Vysokovýkonný bezdrátový USB adaptér 300 Mbit/s Rychlost 11N umožňuje nejlepší streaming videa a zážitek z internetového volání Duální externí antény poskytují lepší výkon při příjmu a přenosu Jednoduché bezdrátové zabezpečení šifrování jedním tlačítkem pomocí tlačítka Rychlé nastavení zabezpečení 1,5m kabel USB umožňuje pohodlné a flexibilní nasazení Podporuje Windows XP / Vista / 7/8 / 8.1, Mac OS X 10.7 ~ 10.10, Linux HARDWARE FEATURES Interface Mini USB 2.0 Button WPS Push Button/Software Dimensions ( W x D x H ) 3.5 x 2.7 x 0.7 in. (90 x 68 x 16.8mm) Antenna Type Dual Omni Directional Antenna Gain 3dBi WIRELESS FEATURES Wireless Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Frequency 2.400-2.4835GHz Signal Rate 11n: Up to 300Mbps(dynamic) 11g: Up to 54Mbps(dynamic) 11b: Up to 11Mbps(dynamic) Reception Sensitivity 270M: -68dBm@10% PER Transmit Power <20dBm(EIRP) Wireless Modes Ad-Hoc / Infrastructure mode Wireless Security Support 64/128 bit WEP, WPA-PSK/WPA2-PSK Modulation Technology DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM Advanced Functions WMM OTHERS Certification CE, FCC, RoHS Package Contents Wireless Adapter TL-WN822N Resource CD Quick Installation Guide 1.5m USB Cable System Requirements Windows 10/8.1/8/7/XP (32/64bit), Mac OS X 10.9-10.13, Linux Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Bezdrátový extender 300 Mbit/s s průchozí zásuvkou TL-WA860RE Režim extenderu zesiluje bezdrátový signál a prodlužuje jeho dosah na dříve nedostupná místa Přidaná zásuvka zajišťuje napájení jiných elektrických zařízení. Miniaturní velikost a nástěnná konstrukce umožňuje snadnou instalaci a flexibilní pohyb 2 pevné externí antény poskytují vynikající bezdrátové pokrytí a spolehlivost Snadné rozšíření pokrytí bezdrátovým signálem po stisknutí tlačítka Range Extender HARDWARE FEATURES Plug Type EU, UK, US Standards and Protocols IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Interface 1 * 10/100Mbps Ethernet Port (RJ45) Button RE (Range Extender) Button, Reset Button Power Consumption About 3W Dimensions ( W x D x H ) 4.3x 2.6 x 3.0in. (110.0 x 65.8 x 75.2mm) Antenna 2 * external WIRELESS FEATURES Frequency 2.4~2.4835GHz Signal Rate 11n: Up to 300Mbps (dynamic) 11g: Up to 54Mbps (dynamic) 11b: Up to 11Mbps (dynamic) Reception Sensitivity 270M: -69dBm@10% PER 130M: -69dBm@10% PER 108M: -69dBm@10% PER 54M: -69dBm@10% PER 11M: -86Bm@8% PER 6M: -89dBm@10% PER 1M: -91dBm@8% PER Transmit Power < 20 dBm (EIRP) Wireless Modes Range Extender/Access Point Wireless Functions WMM (Wi-Fi Multimedia) Wireless MAC Address Filtering Wireless Statistic Domain Login Function Wireless Security 64/128/152-bit WEP WPA-PSK / WPA2-PSK OTHERS Certification CE, RoHS Package Contents 300Mbps Wi-Fi Range Extender with AC Passthrough TL-WA860RE RJ-45 Ethernet Cable Resource CD Quick Installation Guide System Requirements Microsoft® Windows® 98SE, NT, 2000, XP, Vista or Windows 7, 8, 10, Mac® OS, NetWare®, UNIX® or Linux. Environment Operating Temperature: 0°C~40°C (32°F~104°F) Storage Temperature: -40°C~70°C (-40°F~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Venkovní CPE zařízení 5 GHz 300 Mbit/s 13dBi Klientská outdoorová jednotka TP-LINK CPE510 využívá revoluční technologii TP-LINK Pharos MAXtream TDMA (Time-Division-Multiple-Access) a 2x2 MIMO anténu. TP-LINK CPE510 využívá kombinaci 13dBi MIMO 2x2 antény a WiFi radiové části pro pásmo 5 GHz s podporou standardu 802.11a/n (teoreticky až 300 Mbps). Radiová část je umístěna v kvalitním voděodolném IPX5 plastovém boxu podporovány jsou bezdrátové režimy AP / Client / Repeater / AP Router / AP Client Router (WISP). Základní parametry Access Point: Ano Typ zařízení: Access point Operační mód: AP, Klient WLAN (Wifi) standardy: 802.11a, 802.11n Frekvenční rozsah (GHz): 5 Typ antény: Vestavěná Síla anténního signálu: 15 dBi Rozhraní: RJ-4 Počet portů RJ-45: 1 Počet portů HUB/Switche: 1 Přenosové rychlosti pro HUB/Switch [Mb/s]: 100 Přenosové rychlosti pro WLAN (Wifi) [Mb/s]: 150

5 x Aruba Instant On AP25 (RW) 4x4 Wi-Fi 6 Indoor Access Point ( 5 pack ) Model: Instant On AP25Podporované frekvence: 2.4 GHz 5 GHz Bezdrátový datový přenos: 4,8 GbpsDrátový datový přenos: 2,5 Gbps Podporované standardy: 802.11b 802.11a g 802.11n 802.11ac 802.11ax Porty: 1x LAN portŠifrování: WPA3, WPA2-MPSK Typ antény: VšesměrováPodpora externí antény: Ne PoE: Ano Rozměry: 200 x 200 x 45 mmHmotnost: 775g Ultra-high-speed performance for high-density small businesses. Perfect for gaming, boutique hotels, tech start-ups and professional offices. The rise of the remote and hybrid workplace has placed increased pressure on business networks. Existing Wi-Fi infrastructure is struggling to support the explosion of devices and bandwidthhungry applications - all contributing to spotty video calls and sluggish download speeds. The Aruba Instant On AP25, a 4x4 Wi-Fi 6 access point, is designed to meet the increasing volume of connected devices. Delivering superior performance, cov­erage, and speed at a competitive price, the AP25 is the perfect access point for small and growing businesses. The Wi-Fi Certified 6TM AP25 delivers faster Wi-Fi speeds, greater capacity, and reduced latency between access points and devices for a superior Wi-Fi experi­ence. AP25 improves efficiency and reduces congestion for networks with many connected devices, making it ideal for high-density environments. And with 4x the capacity of 802.11ac access points, the AP25 provides exceptional user experience, allowing businesses to serve more customers with higher speed and less congestion. Features of the AP25 include orthogonal frequency-division multiple access (OFDMA), multi-user MIMO and target wake time (TWT). With up to 4 spatial streams (4SS) and 160MHz channel bandwidth (HE160), the AP25 provides groundbreaking wireless capabilities for businesses looking to boost perfor­mance and future-proof their networks. Key Features Ultra-fast 802.11ax, 4x4:4 2.5 Gigabit Ethernet uplink port 160MHz client bandwidth support Mesh backhaul operating at 160MHz1 Wi-Fi CERTIFIED 6TM (Wi-Fi 6) MU-MIMO performance Smart mesh Wi-Fi support Integrated Bluetooth Easy-to-use web and mobile app for setup and management Secure guest Wi-Fi with simple setup Standard Features Next-Generation 802.11ax Wi-Fi Features AP25 is a Wi-Fi CERTIFIED 6TM (Wi-Fi 6) access point that brings higher capacity, efficiency, and performance to small and growing businesses with dense deployments. With a maximum aggregate data rate of 5.3 Gbps, AP25 access points deliver the speed and reliability small businesses need. 2.5g Ethernet Uplink Port And 160mhz Client Bandwidth Support Availability of 2.5G uplink port and wider channel bandwidth delivers faster Wi-Fi speeds for activities like high-def video streaming and gaming. 160mhz Client Bandwidth Support With 160MHz bandwidth support in 11ax, HE160 mode delivers higher performance with 160MHz supported clients. The mesh performance can be doubled with the 160MHz bandwidth support on 5GHz backhaul. Orthogonal Frequency-Division Multiple Access (OFDMA) Allows access points (APs) to handle multiple Wi-Fi 6-capable clients on each channel simultaneously - regardless of device or traffic type. This improves efficiency by boosting overall capacity while reducing latency. Target Wake Time (TWT) Ideal for devices that communicate infrequently, TWT establishes a schedule for clients to communicate with an AP. This helps reduce power consumption, extending battery life. Multiuser, Multiple Input, Multiple Output (MU-MIMO) AP25 supports MIMO, allowing service to multiple clients (Wi-Fi 5 and Wi-Fi 6) at the same time. 1024-Quadrature Amplitude Modulation (1024-QAM) Enables a 25% data increase over 256 QAM, improv­ing throughput to access points and devices. Trusted Platform Module (TPM) All Aruba Instant On access points have an installed TPM for secure storage of credentials, keys, and boot codes. Basic Service Set Coloring (BSS Coloring) Allows the network to assign a "color" tag to a channel and reduce the threshold for interference. Network performance is improved because APs on the same channel can be closer together and still transmit at the same time. Aruba Advanced Cellular Coexistence (ACC) Uses built-in filtering to automatically minimize the impact of interference from cellular networks, distributed antenna systems (DAS), and commercial small-cell or femtocell equipment. Low Density Parity Check (LDPC) Delivers high-efficiency error correction for increased throughput. Transmit Beamforming (TXBF) Delivers increased signal reliability and range. The Instant On Differentiators The Aruba Instant On App Manage everything through our official app on the device of your choice. Manage your network from anywhere, anytime - all from the palm of your hand. Built-In Security Gateway Firewall Stop unwanted people and bots from accessing the network. Leverage advanced features that do not require external gateways - or the complexity that comes with them. Quickly and easily swap it out with another AP in a single click, in case of gateway failure. The new Cloudflare integration provides private and fast web browsing. The 802.11k standard improves roaming performance helping clients connect to nearby APs quickly. Better Together Instant On automatically detects and applies highest (critical) PoE priority to Instant On access points for uninterrupted power delivery and wireless network access. Wired and wireless voice traffic is prioritized with high QoS priority end-to-end for optimal voice performance. Tailored User Experiences Customize guest Wi-Fi experience with logos, authentications, and rules of use. Set data usage per app. Limit duration of use. Use an external portal or service like Facebook Wi-Fi. Create open guest networks for quick and easy access. With the Instant On mobile app, you can apply bandwidth limits for your clients or your network for prioritizing certain primary networks. Enterprise Grade Wi-Fi And Features Control channel and channel width to suit specific environments. Keep users happy as they move between spaces or meetings with a seamless hand­off between APs. Protect users with the robust password-based authentication that WPA3 WPA2 wireless security standard provides. Instant On sup­ports OWE for secure, open Wi-Fi network access at cafes, retail stores and restaurants. Site Inventory and Topology View The site inventory view lists all the Instant On switches and access points on a single interface, and the topology view provides an intuitive structure of all Instant On devices deployed in a network - helping to quickly identify non-functioning devices and troubleshoot accordingly. Network issues can be easily diagnosed with connectivity tests like Ping and Traceroute. Two-Factor Authentication (2FA) As the number of security breaches continue to rise, 2FA has become an essential tool to mitigate risk against compromised login credentials. Two-Factor Authentication (2FA), provides an additional layer of authentication, prevents attackers from remotely accessing your network, and secures your customer information. Multi-Site Management Manage multiple sites, multiple networks, distributed deployments, and multi-tenancy deployments with ease through our cloud-hosted web interface and mobile app. Create unique configurations, statistics, guest portals, and admin read write for every site. Instant On allows three admin accounts per site, offering an option to lock accounts to prevent them from accidental deletion. PPPoE and Static IP Instant On APs can act as routers and handle PPPoE configuration with VLAN support, and they can also act as a DHCP server, providing IP addresses to the wireless network. Assigning a static IP address on an access point allows users to use the same IP address regardless of where the access point is connected, making it easier to access its setup page for any configuration changes. Smart Mesh Extend coverage to hard-to-reach spaces where Eth­ernet cabling may not exist. Set up a mesh network up in minutes through the app - indoors or out. 5-Star Voice and Video Quality Keep users connected via softphones and mobile apps. Automatically detect and prioritize voice and video applications such as Skype, FaceTime, and WeChat that use SIP, SCCP and other popular protocols. No Hidden Fees All features are included in the price of the hardware - there are no recurring subscription or licensing fees. Expert-level support and industry-leading 2-year warranty are also included, along with chat support for the life of the product. Technical Specifications In the Box Aruba Instant On AP25 Indoor Access Point Aruba Instant On AP25 Quick Start Guide Combined ceiling and wall rail mount clip Ethernet cable Radios Dual radio for simultaneous dual-band operation 5 GHz 802.11ax 4x4 MIMO for up to 4.8 Gbps wireless data rate, with Multi User MIMO support (Wi-Fi 6) 2.4 GHz 802.11ax 2x2 MIMO for up to 574 Mbps wireless data rate (Wi-Fi 6) Maximum (Aggregate, Conducted Total) Transmit Power (Limited By Local Regulatory Requirements) 5GHz band: +24dBm (+18dBm per chain, 6dB MIMO gain) 2.4Ghz band: +21dBm (+18dBm per chain, 3dB MIMO gain) Interfaces Uplink 2.5 Gigabit Ethernet port, with PoE-in support (802.3at) DC power connector (12V) Bluetooth Low Energy (BLE) radio LED status indicators (2) Reset LED control button Kensington security slot Physical Specifications 200mm x 200mm x 45mm, excluding mount accessories Weight: 775g Power Power over Ethernet (POE): 802.3at (class 4) Max power consumption (worst-case): 20.1W (PoE), 15.9W (DC) DC power (12V) Notes: Power sources are sold separately unless you purchase the bundle SKU which comes with power options. Antennas Down-tilt omni-directional antennas for 2x2 MIMO with peak antenna gain of 3.77 dBi in 2.4GHz and 4x4 MIMO with peak antenna gain of 4.55 dBi in 5GHz (of the effective, combined pattern for both antennas in each band) Mounting The access point ships with a white mount clip that can attach to both walls and ceilings Mounts that match the design of the APs can be purchased separately Environmental & Reliability Operating temperature: 0° C to +40° C (+32° F to +104° F) MTBF: 670khrs (76yrs) at +25° C Industry Certifications EN 60601-1-1 and EN 60601-1-2 (for deployment in medical environments) Wi-Fi Alliance certified (WFA) 802.11ax with (Wi-Fi 6), WPA2, WPA3 Management Options Instant On mobile application (Android & iOS) Cloud Portal: Portal.ArubaInstantOn.com Warranty & Support Aruba Instant On 2-year* warranty in­cludes 24X7 phone support for the first 90 days and chat support for the entire warranty period. Community support is available for the life of the product. Foundation Care provides extended support for APs. The SKUs are HK1Y0E (3 years) and H30GZE (5 years).

5x Aruba AP-515 (RW) Dual Radio 4x4:4 + 2x2:2 802.11ax Internal Antennas Unified Campus AP ( 5 pack Q9H62A ) Série přístupových bodů Aruba 510 s technologií 802.11ax vysokorychlostní přístup pro mobilní zařízení. Rychlosti dosahují až 4.8 Gb s v pásmu 5GHz a až 575 Mb s v pásmu 2,4Ghz. Každý AP podporuje až 256 klientských zařízení. Odkaz na web výrobce: https: www.arubanetworks.com assets ds DS_AP510Series.pdf SPECIFIKACE Rozhraní E0: HPE SmartRate port (RJ-45, maximum negotiated speed 2.5Gbps) E1: 10 100 1000BASE-T Ethernet network interface (RJ-45) DC power interface: 12Vdc (nominal, + - 5%), accepts 2.1mm 5.5mm center-positive circular plug with 9.5mm length USB 2.0 host interface (Type A connector) Bluetooth 5 and Zigbee (802.15.4) radio Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.5dBi (AP-515) or 4.9dBi (AP-514) Visual indictors (two multi-color LEDs): for System and Radio status Reset button: factory reset, LED mode control (normal off)

10 x Aruba Instant On AP22 (RW) 2x2 Wi-Fi 6 Indoor Access Point ( 10 pack )Aruba Instant On AP22 (RW) Access Point. The Aruba Instant On AP22 provides high-performance concurrent 2.4 GHz and 5 GHz Wi-Fi 6 (802.11ax) features with MIMO radio (2 x 2 at 2.4 GHz, 2 x 2 at 5 GHz) while supporting older 802.11a b g n ac wireless services. Key Features Fast 802.11ax Wi-Fi CERTIFIED 6 (Wi-Fi 6) MU-MIMO performance Support for Smart Mesh Wi-Fi technology Integrated Wi-Fi router gateway Integrated Bluetooth Easy to use web and mobile application for setup and management Secure Wi-Fi for guests with easy setup Technical parameters Dual radio for simultaneous dual band operation 5 GHz 802.11ax 2x2 MIMO for wireless data flow up to 1.2 Gbps, with Multi User MIMO support (Wi-Fi 6) 2.4 GHz 802.11ax 2x2 MIMO for wireless data transfer speeds of up to 574 Mbps (Wi-Fi 6) Uplink Gigabit Ethernet port with PoE-in support (802.3af) DC power connector (12V) Low power Bluetooth radio status indicators (BLE) Reset LED button Kensington security slot Power over Ethernet (POE): 802.3af (Class 3) Maximum power consumption (worst case): 10.1 W (PoE), 8.8 W (DC) DC power supply (12V) Dimensions: 160 mm x 160 mm x 37 mm, excluding mounting accessories Weight: 500 g Aruba Instant On AP22 Indoor Access Points. High-speed Wi-Fi designed with small businesses in mind. Perfect for reimagined offices, schools, and retail hospitality businesses. Small businesses are facing a number of challenges—challenges that need constant attention. The right technology can help you stay on top of them and stay ahead of the curve. Technologies like the ones found inside the AP22. To meet the increasing needs and volumes of connected devices, Aruba Instant On is announcing its first Wi-Fi 6 access point: AP22. Delivering higher capacity and greater performance at a competitive price, the AP22 is the perfect access point for small businesses with expanding mobile, cloud, and IoT requirements. Wi-Fi Certified 6TM AP22 access points deliver faster Wi-Fi speeds, greater capacity, and reduced latency between access points and devices for a superior Wi-Fi experience. With the AP22, you can upgrade your Wi-Fi network to boost performance across devices now, while preparing it for more mobile and IoT devices in the future. Already have a demanding mobile and or IoT environment? Delivering 4x the capacity of 802.11ac access points, AP22 can provide an exceptional user experience in a broad variety of scenarios. Remote offices. Hybrid classrooms. Hotels and restaurants. Reimagined retail and hospitality. The AP22 can handle them all without breaking a sweat. Want to make wires a thing of the past? Combine the AP22 with Smart Mesh Wi-Fi for complete wireless coverage. Want to keep bandwidth hogs and unknown devices off your network? Banish them with the flip of your thumb on the Aruba Instant On App. We know the critical role Wi-Fi plays in business today. No business can’t afford downtime. The Aruba Instant On AP22, at every level, is designed for rapid deployment and simplified management. Be it mounting hardware, or remote device management, or having access to the latest business-grade software, the AP22 lives to make your life easier. Aruba Instant On AP22 Indoor Access Points Key Features Fast 802.11ax, 2X2:2 Wi-Fi CERTIFIED 6TM (Wi-Fi 6) MU-MIMO performance Smart Mesh Wi-Fi support Built-in Wi-Fi router gateway functionality Integrated Bluetooth Easy-to-use web and mobile app for setup and management Secure Guest Wi-Fi with simple setup Application classification, control and visibility Standard Features Orthogonal Frequency-Division Multiple Access (OFDMA) Allows access points (APs) to handle multiple Wi-Fi 6-capable clients on each channel simultaneously—regardless of device or traffic type. This improves efficiency by boosting overall capacity, while reducing latency.. Target Wake Time (TWT) Ideal for IoTs that communicate infrequently, TWT establishes a schedule for when clients need to communicate with an AP. This helps reduce power consumption, extending the battery life of clients. Multiuser, Multiple Input, Multiple Output (MU-MIMO) Allows you to serve multiple clients (Wi-Fi 5 and Wi-Fi 6) at the same time. 1024-Quadrature Amplitude Modulation (1024-QAM) Enables a 25% data increase over 256 QAM, improving throughput in your access points and devices. Trusted Platform Module (TPM) All Aruba Instant On access points have an installed TPM for secure storage of credentials, keys, and boot codes. Basic Service Set Coloring (BSS Coloring) Allows the network to assign a "color" tag to a channel and reduce the threshold for interference. Network performance is improved because APs on the same channel can be closer together and still transmit at the same time—as long as they are different colors. Aruba Advanced Cellular Coexistence (ACC) Uses built-in filtering to automatically minimize the impact of interference from cellular networks, distributed antenna systems (DAS), and commercial small-cell or femtocell equipment. Low Density Parity Check (LDPC) Delivers high-efficiency error correction for increased throughput.. Transmit Beamforming (TxBF) Delivers increased signal reliability and range. The Aruba Instant On App Manage everything through our official app on the device of your choice. Manage your network from anywhere, anytime- all from the palm of your hand. Built-in Security Gateway Firewall Stop unwanted people and bots from accessing your network. Leverage advanced features that do not require external gateways—or the complexity that comes with them. Quickly and easily swap it out with another AP in a single click, in case of gateway failure. Complete App Visibility and Control Get full visibility into the apps running on your network. Block certain applications from being used. Manage this feature straight from the Aruba Instant On app. Tailored User Experiences Customize the experience with logos, authentications, and rules of use. Apply bandwidth rates. Set data usage per app. Limit duration of use. Use an external portal or service like Facebook Wi-Fi. Create open guest networks for quick and easy access. Enterprise Grade Wi-Fi and Features Control network widths, channels, and channel widths to suit your specific environment. Keep users happy as they move between spaces or meetings with a seamless handoff between APs. Just provide secure WPA2 or WPA3 authentication on your networks and we’ll do the rest. Multi-site Management Manage multiple sites, multiple networks, distributed deployments, and multi-tenancy deployments with ease through our cloud-hosted web interface and mobile app. Create unique configurations, statistics, guest portals, and admin read write and read-only privileges for every site. PPPoE and Static IP Every customer has a different environment. They might want to authenticate with the ISP’s PPPoE server and provide static IP to the APs. Smart Mesh Extend coverage to hard-to-reach spaces where Ethernet cabling may not exist. Set up a Mesh network up in minutes through the app—indoors or out. 5-star Voice and Video Quality Keep users connected via softphones and mobile apps. Automatically detect and prioritize voice and video applications such as Skype, FaceTime, and WeChat that use SIP, SCCP and other popular protocols. Technical Specifications WI-FI Radio Specifications Dual radio for simultaneous dual-band operation 5 GHz 802.11ax 2x2 MIMO for up to 1.2 Gbps wireless data rate, with Multi User MIMO support (Wi-Fi 6) 2.4 GHz 802.11ax 2x2 MIMO for up to 574 Mbps wireless data rate (Wi-Fi 6) Maximum (aggregated, conducted total) transmit power (limited by local regulatory requirements): ­ 5GHz band: +21dBm (+18dBm per chain, 3dB MIMO gain) ­ 2.4Ghz band: +21dBm (+18dBm per chain, 3dB MIMO gain) Power Power over Ethernet (POE): 802.3af (class 3) Max power consumption (worst-case): 10.1W (PoE), 8.8W (DC) DC power (12V) Notes: Power sources are sold separately unless you purchase the bundle SKU which comes with power options. Additional interfaces Uplink Gigabit Ethernet port, with PoE-in support (802.3af) DC power connector (12V) Bluetooth Low Energy (BLE) radio LED status indicators (2) Reset LED control button Kensington security slot Antennas Down-tilt omni-directional antennas for 2x2 MIMO with peak antenna gain of 4.3dBi in 2.4GHz and 5.6dBi in 5GHz (of the effective, combined pattern for both antennas in each band). Mounting The access point ships with a white mount clip that can attach to both wall and ceiling. You can also purchase a mount (R6P90A) for aesthetic design and looks of the APs, to blend seamless into your environment. Mounting The access point ships with a white mount clip that can attach to both wall and ceiling. You can also purchase a mount (R6P90A) for aesthetic design and looks of the APs, to blend seamless into your environment. Dimensions and weight Dimensions and weights exclude mount 160 (W) x 160 (D) x 37 mm (H) 6.3 (W) x 6.3 (D) x 1.5 in (H) 500 gm 1.1 lbs Environmental Operating temperature: 0° C to +40° C (32° F to +104° F) Certifications UL 2043 plenum rating EN 60601-1-1 and EN 60601-1-2 (for deployment in medical environments) Wi-Fi Alliance certified (WFA) 802.11ax with (Wi-Fi 6), WPA2, WPA3 Warranty & Support Aruba Instant On 2-Year warranty with 24x7 phone support for first 90 days and chat support for the entire warranty period. Community support as long as you own the products. Should you require longer support, please purchase a Foundation Care contract for your APs. The SKUs are HK1Y0E (3 years) and H30GZE (5 years).

EAP211-Bridge KIT Bezdrôtový most Omada 5 GHz 867 Mb/s vnútorný/vonkajší prístupový bod 802.11ac pro až 867 Mbps pri 5 GHz bezdrôtovej základnej frekvencii.*1 Ideálny profesionálny bezdrôtový prenos na veľké vzdialenosti až do 1 km.*2 Automatické párovanie a agilné LED diódy pre efektívne nasadenie. 3× Gigabit Ethernet porty pre viac vysokorýchlostných pripojení IP kamier. Podporuje vzdialenú a centralizovanú správu Omada SDN pro. IP65 naprogramovať clonu a ochranu pred bleskom 6kV vhodnosť do každého počasia.*3 Podporuje pasívne PoE pre flexibilné nasadenie (adaptér je súčasťou balenia). HARDWARE FEATURES Interface 3x Gigabit Ethernet Ports Button Reset Power Supply 12V DC / 24V Passive PoE (Passive PoE adapter included.) Dimensions ( W x D x H ) 8.8 x 3.1 x 2.4 in (224 × 79 × 60 mm) Antenna Type Internal 2×2 Dual-polarized directional MIMO antennas 5 GHz: 7.0 dBi Horizontal:70°, Vertical: 70° Weatherproof Enclosure IP65 Mounting Pole Mounting (Accessories included) WIRELESS FEATURES Coverage 1000m(3280ft)5 Wireless Standards IEEE 802.11 a/b/g/n/ac Frequency 5 GHz Signal Rate 5 GHz: Up to 867 Mbps Wireless Functions • Mesh*4 • MU-MIMO: 5G 2x2 MU-MIMO DL • Load Balance • Beamforming • Airtime Fairness • Multiple SSIDs:8 • Wireless Statistics • Wireless Schedule • Reboot Schedule • RADIUS Accounting • MAC Authentication • Static IP/Dynamic IP Wireless Security • VLAN • Access Control • Rogue AP Detection • Captive Portal Authentication*4 • Maximum number of MAC Filter: 4,000 • WPA-Personal/Enterprise, WPA2-Personal/Enterprise Transmission Power • CE: <23dBm (5 GHz, band 1/2, EIRP); <30dBm (5 GHz band3, EIRP); • FCC: <22dBm (5 GHz band1/4) MANAGEMENT Omada App Yes Restore & Backup Yes Firmware update via Web Yes NTP Yes Centralized Management • Omada Hardware Controller (OC300) • Omada Hardware Controller (OC200) • Omada Software Controller • Omada Cloud-Based Controller Cloud Access Yes. Require the use of OC300, OC200, the Omada Software Controller, or Omada Cloud-Based Controller. LED ON/OFF Control Yes Management MAC Access Control Yes SNMP v1, v2c, v3 SSH Yes Web-based Management Yes OTHERS Certification CE, FCC, RoHS Package Contents • EAP211-Bridge KIT • Passive PoE Adapter • Power Cord • Installation Guide • Mounting Kit Environment • Operating Temperature: -40 °C–70 °C (-40 °F–158 °F); • Storage Temperature: -40 °C–70 °C (-40 °F–158 °F); • Operating Humidity: 10%–90% non-condensing; • Storage Humidity: 5%–90% non-condensing

HARDWARE FEATURES Interface • Uplink: 1× 10/100/1000 Mbps Ethernet Port • Downlink: 1× 10/100/1000 Mbps Ethernet Port Physical Security Lock No Button LED/Wi-Fi Button, RESET Power Supply 802.3af/802.3at PoE Power Consumption 7 W Dimensions 3.4 × 3.4 × 1.2 in (86.8 × 86.8 × 30.2 mm) Antenna 2 Dual-Band Antennas • 2.4 GHz: 2× 4 dBi • 5 GHz: 2× 3.6 dBi Mounting Wall Plate Mounting Hardware Watch Dog Yes WIRELESS FEATURES Wireless Standards IEEE 802.11n/g/b/ac Frequency 2.4 GHz and 5 GHz Signal Rate • 5 GHz: Up to 867 Mbps • 2.4 GHz: Up to 300 Mbps Wireless Functions • 16 SSIDs (Up to 8 SSIDs on each band) • Enable/Disable Wireless Radio • Automatic Channel Assignment • Transmit Power Control (Adjust Transmit Power on dBm) • QoS(WMM) • Load Balance • Rate Limit • Reboot Schedule • Wireless Schedule • Wireless Statistics based on SSID/AP/Client • MU-MIMO • Band Steering • Beamforming Wireless Security • Captive Portal Authentication • Access Control • Wireless Mac Address Filtering • Wireless Isolation Between Clients • SSID to VLAN Mapping • Local LAN port based VLAN • Rogue AP Detection • 802.1X Support • 64/128/152-bit WEP / WPA / WPA2-Enterprise, WPA-PSK / WPA2-PSK Transmission Power CE: • ?20 dBm (2.4 GHz, EIRP) • ?23 dBm (5 GHz, EIRP) MANAGEMENT Omada App Yes Centralized Management • Omada Cloud-Based Controller • Omada Hardware Controller (OC300) • Omada Hardware Controller (OC200) • Omada Software Controller Cloud Access Yes (Through OC300, OC200, Omada Cloud-Based Controller, or Omada Software Controller) Email Alerts Yes LED ON/OFF Control Yes Management MAC Access Control Yes SNMP v1,v2c System Logging Local/Remote Syslog Local/Remote Syslog SSH Yes Web-based Management HTTP/HTTPS L3 Management Yes Multi-site Management Yes Management VLAN Yes OTHERS Certification CE, RoHS Package Contents • Omada AC1200 Wireless MU-MIMO Gigabit Wall-Plate Access Point EAP230-Wall • Installation Guide • Mounting Screw System Requirements Microsoft Windows XP, Vista, Windows 7, Windows 8, Windows10 Environment • Operating Temperature: 0–40 ? (32–104 ?) • Storage Temperature: -40–70 ? (-40–158 ?) • Operating Humidity: 10–90% RH non-condensing • Storage Humidity: 5–90% RH non-condensing

Pri zakúpení tohto výrobku získate ako darček internetovú televíziu na 1 mesiac zdarma. Balíček základ 1 mesiac obsahuje 66 kanálov na 1 mesiac. K tomu 25 hodín nahrávania a 50 hodín spätného sledovania. Pre získanie IP TV je nutné zakúpený produkt registrovať na stránke www.tplink.tv Bezdrátový Extender AC1200 RE305 Oživí mrtvé zóny ve Wi-Fi síti díky silnému rozšíření s kombinovanou rychlostí přenosu dat až 1,2Gbit/s Pracuje vobou pásmech 2,4GHz (300Mbit/s) i 5GHz (867Mbit/s) a zajistí stabilnější používání bezdrátové sítě Inteligentní kontrolka signálu pomáhá díky indikaci síly signálu najít pro extender nejlepší umístění, aby pokrytí Wi-Fi signálem bylo optimální Pracuje s jakýmkoli Wi-Fi routerem nebo bezdrátovým access pointem HARDWARE FEATURES Plug Type EU, UK, US Standards and Protocols IEEE802.11ac, IEEE 802.11n, IEEE 802.11g, IEEE 802.11a, IEEE 802.11b Interface 1 x 10/100M Ethernet Port (RJ45) Button WPS Button, Reset Button Power Consumption 7.3W(max power consumption) Dimensions ( W x D x H ) 3.1 x 3.0 x 3.0 in. (80 x 78 x 77mm) Antenna 2 x external WIRELESS FEATURES Frequency 2.4GHz & 5GHz(11ac) Signal Rate 5GHz:Up to 867Mbps 2.4GHz:Up to 300Mpbs Reception Sensitivity 5GHz: 11a 6Mbps:-91dBm@10% PER 11a 54Mbps: -74dBm@10% PER 11ac HT20 mcs8: -68dBm@10% PER 11ac HT40 mcs9: -63dBm@10% PER 11ac HT80 mcs9: -59dBm@10% PER 2.4GHz 11g 54M: -79dBm@10% PER 11n HT20 mcs7: -77dBm@10% PER 11n HT40 mcs7: -74dBm@10% PER Wireless Modes Range Extender/Access Point Wireless Statistic Concurrent Mode boost both 2.4G/5G Wi-Fi band Wireless Functions Wireless Statistic Concurrent Mode boost both 2.4G/5G Wi-Fi band Access Control LED Control Domain Login Function Wireless Security 64/128-bit WEP WPA-PSK / WPA2-PSK Transmission Power <17dBm(2.4GHz) <17dBm(5GHz) OTHERS Certification CE, FCC, RoHS Package Contents AC1200 Wi-Fi Range Extender RE305 Quick Installation Guide Box Dimensions (W X D X H) 6.15 x 4 x 3.7 in. (156.5 x 101.5 x 95mm) System Requirements Microsoft® Windows® 98SE, NT, 2000, XP, Vista or Windows 7, 8, 10, Mac® OS, NetWare®, UNIX® or Linux. Environment Operating Temperature: 0°C~40°C (32°F~104°F) Storage Temperature: -40°C~70°C (-40°F~158°F) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

EAP245 AC1750 MU-MIMO bezdrôtový gigabitový prístupový bod pre montáž na strop Rýchla dvojpásmová sieť WiFi: Simultánne rýchlosti 450 Mbit/s v pásme 2,4 GHz a 1 300 Mbit/s v pásme 5 GHz poskytujú výslednú prenosovú rýchlosť 1 750 Mbit/s v sieti WiFi.† Integrované do platformy Omada SDN: Funkcia ZTP (Zero-Touch Provisioning)‡, centralizovaná cloudová správa a inteligentné monitorovanie. Centralizovaná správa: Cloudový prístup a aplikácia Omada pre maximálne pohodlie a jednoduchú správu. Bezproblémový roaming: Užívatelia sa môžu voľne pohybovať v pokrytej oblasti bez toho, aby to malo nejaký vplyv na streamovanie videa a hlasové hovory.* Podpora technológie PoE: Podporuje štandard 802.3af/at aj pasívne PoE napájanie (PoE adaptér sa predáva samostatne) pre flexibilné možnosti inštalácie. Zabezpečená sieť pre hostí: Poskytuje niekoľko možností overovania (SMS / Voucher atď.) a rad technológií pre zabezpečenie bezdrôtovej siete.* Pokročilé bezdrôtové technológie: Optimalizujte výkon siete pomocou technológií MU-MIMO, Band Steering, Airtime Fairness a Beamforming. HARDWARE FEATURES Interface 2 × Gigabit Ethernet (RJ-45) Port (One port supports IEEE802.3af PoE and Passive PoE) Physical Security Lock Yes Button Reset Power Supply • 802.3af/at PoE • 48V Passive PoE (+4,5pins; -7,8pins. PoE Adapter Included) Power Consumption 12.3 W Dimensions ( W x D x H ) 8.1 × 7.1 × 1.5 in (205.5 × 181.5 × 37.1 mm) Antenna Type Internal Omni • 2.4 GHz: 3× 3.5 dBi • 5 GHz: 3× 4 dBi Mounting Ceiling /Wall Mounting (Kits included) WIRELESS FEATURES Wireless Standards IEEE 802.11ac/n/g/b/a Frequency 2.4GHz and 5GHz Signal Rate • 5 GHz:Up to 1300 Mbps • 2.4 GHz:Up to 450 Mbps Wireless Functions • Multiple SSIDs (Up to 16 SSIDs, 8 for each band) • Enable/Disable Wireless Radio • Automatic Channel Assignment • Transmit Power Control (Adjust Transmit Power on dBm) • QoS(WMM) • MU-MIMO • Seamless Roaming* • Omada Mesh* • Band Steering • Load Balance • Airtime Fairness • Beamforming • Rate Limit • Reboot Schedule • Wireless Schedule • Wireless Statistics based on SSID/AP/Client Wireless Security • Captive Portal Authentication* • Access Control • Wireless Mac Address Filtering • Wireless Isolation Between Clients • SSID to VLAN Mapping • Rogue AP Detection • 802.1X Support • 64/128/152-bit WEP / WPA / WPA2-Enterprise, • WPA-PSK / WPA2-PSK Transmission Power • CE: ?20 dBm (2.4GHz) ?23 dBm (5GHz) • FCC: ?24 dBm (2.4 GHz) ?24 dBm (5 GHz) MANAGEMENT Omada App Yes Centralized Management • Omada Cloud-Based Controller • Omada Hardware Controller (OC300) • Omada Hardware Controller (OC200) • Omada Software Controller Cloud Access Yes (Through OC300, OC200, Omada Cloud-Based Controller, or Omada Software Controller) Email Alerts Yes LED ON/OFF Control Yes Management MAC Access Control Yes SNMP v1, v2c System Logging Local/Remote Syslog Local/Remote Syslog SSH Yes Web-based Management HTTP/HTTPS L3 Management Yes Multi-site Management Yes Management VLAN Yes Zero-Touch Provisioning Yes. Requiring the use of Omada Cloud-Based Controller. OTHERS Certification CE, FCC, RoHS Package Contents • 5 EAP245 Access Points • 5 Mounting Kits • 1 Installation Guide System Requirements Microsoft Windows XP, Vista, Windows 7, Windows 8, Windows10, Linux Environment • Operating Temperature: 0–40 ? (32–104 ?) • Storage Temperature: -40–70 ? (-40–158 ?) • Operating Humidity: 10–90% RH non-condensing • Storage Humidity: 5–90% RH non-condensing

AC750 Bezdrátový router na cesty TL-WR902AC Design vhodný na cesty – je pohodlně malý a lehký, takže jej snadno zabalíte a vezmete s sebou kamkoli a vytvoříte si vlastní Wi-Fi síť přes Ethernet, z připojeného 3G/4G USB modemu nebo poskytovatele bezdrátového připojení internetu (WISP) AC750 má dvoupásmovou Wi-Fi – Silné a rychlé připojení pro streaming HD videa na všech vašich zařízeních Jeden přepínač pro různé režimy – Ideální pro Wi-Fi doma, v hotelovém pokoji nebo na cestách Flexibilní napájení – přes port micro USB z adaptéru, přenosné nabíječky nebo notebooku Všestranný USB port – pro sdílení souborů nebo přístup k internetu přes 3G/4G USB modem HARDWARE FEATURES Interface 1 10/100Mbps WAN/LAN Port 1 Reset Button 1 USB 2.0 Port 1 Mode Switch 1 WPS Button External Power Supply 5V/2A Dimensions ( W x D x H ) 2.91*2.64*0.87 in. (74*67*22mm) Antenna Type On-Board WIRELESS FEATURES Wireless Standards IEEE 802.11ac/n/a 5GHz IEEE 802.11b/g/n 2.4GHz Frequency 2.4GHz and 5GHz Signal Rate 5GHz: Up to 433Mbps(Only with 11AC Wireless Adapter); Up to 150Mbps with 11N Wireless Adapter 2.4GHz: Up to 300Mbps Reception Sensitivity 11a 54M: -76dBm; 11ac VHT20 MCS8: -70dBm; 11ac VHT40 MCS9: -65.5dBm; 11ac VHT80 MCS9: -61.5dBm 2.4GHz: 11g 54M: -76dBm11n; HT20 MCS7: -74dBm; 11n HT40 MCS7: -71dBm Transmit Power CE: <20dBm(2.4GHz) <23dBm(5GHz) Wireless Functions Enable/Disable Wireless Radio, WDS Bridge, WMM, Wireless Statistics Wireless Security 64/128-bit WEP,WPA / WPA2,WPA-PSK/ WPA2-PSK encryption SOFTWARE FEATURES Quality of Service WMM, Bandwidth Control Management Access Control Local Management Remote Management WAN Connection Type Dynamic IP/Static IP/PPPoE/ PPTP(Dual Access)/L2TP(Dual Access) DHCP Server, Client, DHCP Client List, Address Reservation Port Forwarding Virtual Server, Port Triggering, UPnP, DMZ Dynamic DNS DynDns, Comexe, NO-IP VPN Pass-Through PPTP, L2TP, IPSec Access Control Parental Control, Local Management Control, Host List, Access Schedule, Rule Management Firewall Security DoS, SPI Firewall, IP Address Filter/Domain Filter, IP and MAC Address Binding Protocols Supports IPv4 Guest Network 2.4GHz guest network × 1 5GHz guest network × 1 OTHERS Certification CE, FCC, RoHS Package Contents AC750 Wireless Travel Router TL-WR902AC Power Adapter RJ45 Ethernet Cable Quick Installation Guide System Requirements Windows 10/8.1/8/7/Vista/XP, Mac OS or Linux-based operating system Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Přístupový bod AP6 Professional Professional Outdoor od Alta Labs má kompaktní tvar, elegantní design, IP68 certifikaci a umožňuje tak bezproblémovou integraci do venkovních prostor jako jsou kampusy, univerzitní areály, sportovní areály atd. AP6-PRO Outdoor je napájen pouze přes ethernet pro jednoduchou a čistou instalaci a díky plastové průchodce zajišťuje bezpečnou instalaci ve venkovním prostředí. Mimořádně dobrou práci odvedli tvůrci u jednotlivých funkcí jako je spolehlivý roaming řešený přes 802.11r k v standardy, ověřování více hesly při stejném SSID pro oddělení sítí na základě hesla, nebo blokování obsahu pomocí DPI enginu, které nevyžaduje žádný další hardware a ani nesnižuje propustnost Access Pointu. Přístupový bod AP6 Professional Professional Outdoor od Alta Labs má kompaktní tvar, elegantní design, IP68 certifikaci a umožňuje tak bezproblémovou integraci do venkovních prostor jako jsou kampusy, univerzitní areály, sportovní areály atd. AP6-PRO Outdoor je napájen pouze přes ethernet pro jednoduchou a čistou instalaci a díky plastové průchodce zajišťuje bezpečnou instalaci ve venkovním prostředí. Mimořádně dobrou práci odvedli tvůrci u jednotlivých funkcí jako je spolehlivý roaming řešený přes 802.11r k v standardy, ověřování více hesly při stejném SSID pro oddělení sítí na základě hesla, nebo blokování obsahu pomocí DPI enginu, které nevyžaduje žádný další hardware a ani nesnižuje propustnost Access Pointu. Ověření více hesly Inovativní přístup k oddělení sítí pomocí různých hesel k Wi-Fi namísto vytváření virtuálních SSID vám umožní zvýšit propustnost sítě. Každé heslo může být spojeno s konkrétním omezením rychlosti, nastavenou VLAN, kalendářem vypnutí Wi-Fi, nebo hotspotem. Deep Packet Inspection Engine Blokování obsahu podle aplikace, výběr z rozsáhlého předdefinovaného seznamu včetně možného blokování dle domény a to vše bez snížení propustnosti a nutnosti pořizování dalšího HW Klíčové vlastnosti • Management přes Cloud - kdykoliv, odkudkoliv a ZDARMA (prohlížeč, mobilní aplikace) • Vysoce výkonná Wi-Fi 6 s benefity z Wi-Fi 7 - až 4096 QAM • 2x2 MIMO (2.4 GHz) a 4x4 MIMO (5 GHz), 573 + 5800 Mbps • Gigabitový LAN s napájením přes PoE • Krytí IP68 - vhodné pro integraci ve venkovním prostředí • Podpora VLAN, QoS, Multi SSID a šifrování WPA3 • Roaming řešen pomocí standardů 802.11r k v • Ověření více hesly • Deep Packet Inspection Engine • Hotspot stránka - vytvořte si vlastní logovací stránku s logem, smluvními podmínkami s možností pro přesměrování na externí URL • Barevné kódování bezdrátových sítí - funkce která vám umožňuje přiřadit bezdrátové SSID do skupin a ty poté přiřadit jednotlivým AP • Intuitivní přehled o AP a připojených zařízeních, statistiky... Obsah balení • Zařízení • Držák na stěnu a na stožár • Šroubky, hmoždinky • (2) kovová stahovací páska Bezdrátové vlastnosti Bezdrátové frekvence 2.4 + 5 GHz (dual band) WiFi standardy 802.11ax, 802.11ac, 802.11n, 802.11a, 802.11b g Přenosová rychlost - 2.4GHz [Mb s] 574 Přenosová rychlost - 5GHz [Mb s] 5800 Vysílací výkon 2.4GHz [dBm] 23 Vysílací výkon 5GHz [dBm] 26 Šifrování WPA, WPA2, WPA3 2.4GHz MIMO 2 x 2 5GHz MIMO 4 x 4 Typ antény Vestavěná Počet vestavěných antén 4 Roaming Ano Zisk antény [dBi] 3,3, 4,3 Konektory a rozhraní Rychlost LAN (1) 10 100 1000Mbps Ostatní Bluetooth Napájení Napájení přes PoE 802.3at, 42 .. 57V DC Typ napájení PoE Typy PoE PoE-In (pouze) Max. spotřeba energie [W] 25 Fyzické charakteristiky Stupeň krytí IP68 Použití Venkovní Tlačítka Reset Provozní teplota [°C] -40 až 70 Hmotnost [g] 900 Hloubka [mm] 90 Šířka [mm] 125 Výška [mm] 190 Software Operační mód Access Point Management Alta Labs Controller Výchozí IP adresa Dynamická z DHCP Výchozí jméno a heslo Nastavuje se při prvním spuštění

Aruba AP-OUT-MNT-V1A, WLAN access point mount, Aruba AP-584/AP-585

Aruba AP-515 (RW) Dual Radio 4x4:4 + 2x2:2 802.11ax Internal Antennas Unified Campus AP Série přístupových bodů Aruba 510 s technologií 802.11ax vysokorychlostní přístup pro mobilní zařízení. Rychlosti dosahují až 4.8 Gb s v pásmu 5GHz a až 575 Mb s v pásmu 2,4Ghz. Každý AP podporuje až 256 klientských zařízení. Odkaz na web výrobce: https: www.arubanetworks.com assets ds DS_AP510Series.pdf SPECIFIKACE Rozhraní E0: HPE SmartRate port (RJ-45, maximum negotiated speed 2.5Gbps) E1: 10 100 1000BASE-T Ethernet network interface (RJ-45) DC power interface: 12Vdc (nominal, + - 5%), accepts 2.1mm 5.5mm center-positive circular plug with 9.5mm length USB 2.0 host interface (Type A connector) Bluetooth 5 and Zigbee (802.15.4) radio Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 3.5dBi (AP-515) or 4.9dBi (AP-514) Visual indictors (two multi-color LEDs): for System and Radio status Reset button: factory reset, LED mode control (normal off)

Přístupové body řady Aruba 530 Campus s technologií IEEE 802.11ax jsou navrženy tak, aby poskytovaly extrémně výkonný přístup pro mobilní zařízení v místech s velkým počtem zařízení. Aruba 530 Series využívá funkce 802.11ax pro efektivní obsluhu více klientů, což zvyšuje rychlost přenosu dat pro jednotlivá zařízení i celkový systém. Řada 530 podporuje maximální přenosové rychlosti 2,4 Gbps v pásmu 5GHz a 1 150 Mb/s v pásmu 2,4 GHz (pro agregovanou špičkovou rychlost dat 3,55 Gbps). Každý AP podporuje až 1024 přidružených klientských zařízení na jeden přístupový bod, což činí špičkové AP 802.11ax řady 530 ideální pro prostředí s vysokou hustotou provozu. Přehled *Rozhraní: (2) Port HPR SmartRate RJ-45 (maximální rychlost 5 Gbps) *Montáž: Montážní držák předinstalován na zadní straně AP. Tento držák se používá k zajištění AP k některé z Aruba montážních sad (prodává se samostatně). *Napájení: IEEE 802.3bt (třída 5) nebo 802.3at PoE nebo přímý stejnosměrný proud (přes volitelné napájení) *Wi-Fi anténa: Čtyři RP-SMA konektory pro externí dvoupásmové antény. *Maximální rychlost přenosu dat: 2,4 Gb/s v pásmu 5GHz a 1 150 Mb/s v pásmu 2,4 GHz *Rozměry (VxŠxH): 57 x 240 x 240 mm *Hmotnost: 1,0 kg

Aruba AP-615 (RW) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP Aruba 610 Series Campus Access Points Fast, Resilient, and Secure Wi-Fi 6E Connectivity in a Compact and Affordable Platform For enterprises who need more wireless capacity and or wider channels, Aruba 610 Series Campus APs are designed to take advantage of the newly available 6 GHz spectrum using a unique dual-radio tri-band architecture. Adding support for the 6 GHz band to the traditional 2.4 GHz and 5 GHz bands more than doubles the available wireless capacity in a wireless network - so you can meet growing demand due to bandwidth-hungry video, increasing numbers of client and IoT devices, and growth in cloud. Unique to Aruba, the 610 Series features two radios that can be tuned to any two of the three available spectrum bands for Wi-Fi (2.4 GHz, 5 GHz, 6 GHz). This flexibility provides a cost-effective and compact platform that delivers full tri-band coverage as part of a multi-AP deployment and can be used with software that will intelligently and flexibly configure the radios of each of these dual-radio APs. Key Features Unlocks the 6 GHz band to more than double the available capacity in wireless networks Comprehensive dual radio tri-band coverage across 2.4 GHz, 5 GHz, and 6 GHz to deliver up to 3.6 Gbps combined peak data rate1 Compact and low power consumption - virtually unrestricted operation from an 802.3af (class 3) PoE source2 Up to seven 160 MHz channels in 6 GHz to support low-latency, bandwidth-hungry applications like high-definition video, and augmented reality virtual reality applications 2.5 Gbps Smart Rate Ethernet port to minimize wired bottlenecks Built-in GPS receivers and fine time measurement (802.11mc) to enable APs to automatically locate themselves and serve as reference points for accurate indoor location measurements Notes: ­ 1When configured for 5 GHz + 6 GHz operation ­ 2By default (with IPM disabled) the AP-615 will disable the USB port and limit the speed of the Ethernet port to 1Gbps when on class 3 POE. The Intelligent Power Monitoring feature can be used to avoid these restrictions Standard Features More Capacity and Wider Channels The Aruba 610 Series APs are designed to take advantage of Wi-Fi 6E and the 6 GHz band, which translates into far greater speeds, wider channels for multi-gigabit traffic, and less interference. Its two 2x2 MIMO radios deliver a combined peak data rate of up to 3.6 Gbps when configured for concurrent 5 GHz and 6 GHz operation. Advantages of 6 GHz Wi-Fi 6E provides up to 1200 MHz of additional unlicensed spectrum in the 6 GHz band for higher throughput and improved application performance. With up to seven 160 MHz channels, Wi-Fi 6E can better support low-latency, bandwidth hungry applications like high-definition video and augmented reality virtual reality applications. Only Wi-Fi 6E capable devices can use the 6 GHz band so there is no interference or slowdowns due to legacy devices. Device Class Support The Aruba 610 Series APs are part of the low power indoor (LPI) device class. This fixed indoor-only class uses lower power levels and does not require an Automated Frequency Coordination service (AFC) to manage incumbent outdoor services, which is required for standard class APs. Global Readiness While the need for more Wi-Fi capacity is recognized across the globe, countries are approaching the 6 GHz band differently. The 610 Series APs are set up to automatically update regulatory rules once Wi-Fi 6E regulations have been approved and certified. Extend the Benefits of Wi-Fi 6 The Aruba 610 Series APs are based on the 802.11ax (Wi-Fi 6) standard, which means that all its efficiency and security enhancements are also available on the 6 GHz band. Wi-Fi 6 features such as Orthogonal Frequency Division Multiple Access (OFDMA), BSS coloring etc. are fully supported on the Aruba Wi-Fi 6E access points as well. Advantages of OFDMA The Aruba 610 Series is equipped with OFDMA to handle multiple 802.11ax capable clients on each channel simultaneously, regardless of device or traffic type. Channel utilization is optimized by handling each transaction via smaller sub-carriers or resource units (RUs), which means that clients are sharing a channel and not competing for airtime and bandwidth. Wi-Fi Optimization Client Optimization Aruba's patented AI-powered technology eliminates sticky client issues by steering a client to the AP where it receives the best radio signal. ClientMatch steers traffic from the noisy 2.4 GHz band to the preferred 5 GHz or 6 GHz band depending on client capabilities and AP setttings. ClientMatch also dynamically steers traffic to load balance APs to improve the user experience. Automated Wi-Fi Radio Frequency Management To optimize the user experience and provide greater stability, Aruba AirMatch allows organizations to automate network optimization using machine learning. AirMatch provides dynamic bandwidth adjustments to support changing device density, enhanced roaming using an even distribution of Effective Isotropic Radiated Power (EIRP) to radios, and real-time channel assignments to mitigate co-channel interference. AirMatch also ensures that the two radios of Aruba 610 Series Access Points are automatically configured in the most effective and efficient way to deliver full tri-band coverage. Application Assurance With Aruba Air Slice, organizations can provide application assurance to their users that goes beyond the traditional capabilities of airtime fairness. After the SLAs are configured, Air Slice monitors network usage, automatically allocates radio resources, and dynamically adjusts radio resources as new users connect and applications sessions begin or end. Aruba Advanced Cellular Coexistence (ACC) Unique to Aruba, Advanced Cellular Coexistence uses built-in filtering to automatically minimize the impact of interference from cellular networks, distributed antenna systems (DAS), and commercial small cell or femtocell equipment. Intelligent Power Monitoring (IPM) For better insights into energy consumption, Aruba APs continuously monitor and report hardware energy usage. Unlike other vendor's access points, Aruba APs can also be configured to enable or disable capabilities based on available PoE power - ideal when wired switches have exhausted their power budget. Enterprises can deploy Wi-Fi 6E APs and update switching and power at a later if needed based on their actual usage. Self-Locating APs Indoor location shouldn't require guesswork or costly overlay technologies. Aruba's Wi-Fi 6 and 6E APs help organizations leverage their wireless investment to deliver indoor location - everywhere. Aruba 610 Series Campus APs include built-in GPS receivers and intelligent software to allow them to automatically locate themselves accurately within the universal framework of latitude and longitude. As part of Aruba's indoor location services solution, they serve as reference points for client devices using fine time measurements (802.11mc) and other location technologies. In addition, Aruba's Wi-Fi 6 and 6E APs support Open Locate, an emerging standard that allows APs to share their location over the air and through cloud-based APIs, enabling mobile devices to locate themselves and applications to support network analytics. APs as an IoT transport platform The Aruba 610 Series includes an integrated Bluetooth 5 and 802.15.4 radio for Zigbee support to simplify deploying and managing IoT-based location services, asset tracking services, security solutions, and IoT sensors. There is also a USB-port extension to provide IoT connectivity to a wider range of devices. These IoT capabilities allows organizations to leverage Aruba APs as an IoT transport platform, which eliminates the need for an overlay infrastructure and additional IT resources and can accelerate IoT initiatives. In addition, Target Wake Time (TWT), part of the 802.11ax standard, establishes a schedule for when clients need to communicate with an AP. This helps improve client power savings and reduces airtime contention with other clients, which is ideal for IoT. Aruba secure infrastructure The Aruba 610 Series includes build-security capabilities such as: WPA3 and Enhanced Open Support for stronger encryption and authentication is provided via the latest version of WPA for enterprise-protected networks. Enhanced Open offers seamless new protection for users connecting to open networks where each session is automatically encrypted to protect user passwords and data on guest networks. WPA2-MPSK MPSK enables simpler passkey management for WPA2 devices - should the Wi-Fi password on one device or device type change, no additional changes are needed for other devices. This capability requires Aruba ClearPass Policy Manager. Simple and Secure Access To improve security and ease of management, IT can centrally configure and automatically enforce role-based policies that define proper access privileges for employees, guests, contractors, and other user groups - no matter where users connect on wired and WLANs. Dynamic Segmentation eliminates the time consuming and error-prone task of managing complex and static VLANs, ACLs, and subnets by dynamically assigning policies and keeping traffic secure and separated. Seamless Handoffs to Cellular Built on the technical foundations of Passpoint and Wi-Fi Calling, Aruba Air Pass creates a roaming network across the Aruba enterprise customer footprint, extending cellular coverage and enhancing the visitor and subscriber experience to deliver a great experience for your guests while reducing costs and management overhead for DAS. Flexible Operation and Management Our APs can operate as standalone access points or with a gateway for greater scalability, security, and manageability. APs can be deployed using zero touch provisioning - without on-site technical expertise - for ease of implementation in branch offices and for remote work. Aruba APs can be managed using cloud-based or on-premises solutions for any campus, branch, or remote work environment. As the management and orchestration console for Aruba ESP (Edge Services Platform), Aruba Central provides a single pane of glass for overseeing every aspect of wired and wireless LANs, WANs, and VPNs. AI-powered analytics, end-to-end orchestration and automation, and advanced security features are built natively into the solution. Summary Aruba 610 Series Access Points are designed to take advantage of the 6 GHz band using two radios that can deliver comprehensive tri-band coverage in a multi-AP environment and better meet the growing demands of Wi-Fi due to increased use of video, growth in client and IoT devices, and expanded use of cloud. With a 3.6 Gbps combined peak data rate for higher throughput and faster speeds for indoor use, the Aruba 610 Series delivers a cost-effective enterprise Wi-Fi 6E solution with increased capacity, wider channels, reduced power consumption. BTO Models 615 Internal Antenna Access Points Rule # Description SKU Aruba AP-615 (EG) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J46A Aruba AP-615 (IL) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J47A Aruba AP-615 (JP) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J48A Aruba AP-615 (RW) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J49A Aruba AP-615 (US) Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J50A 615 Internal Antenna Access Points - TAA Models Rule # Description SKU Aruba AP-615 (EG) TAA Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J51A Aruba AP-615 (IL) TAA Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J52A Aruba AP-615 (JP) TAA Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J53A Aruba AP-615 (RW) TAA Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J54A Aruba AP-615 (US) TAA Dual-radio Tri-band 2x2:2 802.11ax Wi-Fi 6E Internal Antennas Campus AP R7J55A Notes: ­ Add Mount Kit ­ OCA Only Model Selection Form - HPE Offering Aruba Wireless Access Points Campus: Aruba 610 Series Campus Access Points Mount Accessories AP Mount Kits Rule # Description SKU AP-MNT-A Campus AP mount bracket kit (individual) type A: suspended ceiling rail flat 9 16 R3J15A 1 HPE Aruba Networking AP-MNT-MP10-A Campus AP 10-Pack 9 16 Flat Ceiling Rail Mount Bracket Kit JZ370A AP-MNT-B Campus AP mount bracket kit (individual) type B: suspended ceiling rail flat 15 16 R3J16A 1 HPE Aruba Networking AP-MNT-MP10-B Campus AP 10-Pack 15 16 Flat Ceiling Rail Mount Bracket Kit Q9G69A 1 HPE Aruba Networking AP-MNT-MP10-B1 Campus AP 10-Pack 15 16 Adj Flat Ceiling Rail Mount Bracket Kit R6T34A AP-MNT-C Campus AP mount bracket kit (individual) type C: suspended ceiling rail profile 9 16 R3J17A 1 HPE Aruba Networking AP-MNT-MP10-C Campus AP 10-Pack Profile 9 16 Ceiling Rail Mount Bracket Kit Q9G70A AP-MNT-D Campus AP mount bracket kit (individual) type D: solid surface R3J18A 1 HPE Aruba Networking AP-MNT-MP10-E Campus AP 10-Pack Wall-box Mount Bracket Kit Q9G71A AP-MNT-E Campus AP mount bracket kit (individual) type E: wall-box R3J19A 1 HPE Aruba Networking AP-MNT-MP10-E Campus AP 10-Pack Wall-box Mount Bracket Kit R1C72A 1 HPE Aruba Networking AP-MNT-MP10-U Campus AP Universal Mount Bracket Kit (10-pack) S0J40A 1 AP-MNT-MP10-X Campus AP mount adapter kit (10-pack) R3T20A Configuration Rules Rule # Description 1 OCA Display Notes: Kit contains mounts for 10 access points Notes: Clic Warning: Access Points do not include a Mount. Qty 1 Mount kits should be selected. Power Options Power Options Rule # Description SKU 1 AP-AC2-12B 12V 48W AC DC desktop style power adapter with 2.1 5.5mm connector R3K00A Add AC power cord 1 AP-POE-AFGE 1-Port GbE 802.3af 15.4W midspan injector R6P68A Add AC power cord USB port disabled (when IPM disabled) 1 AP-POE-ATSR 1-Port Smart Rate 802.3at 30W midspan injector R6P67A Add AC power cord Configuration Rules Rule # Description 1 If this Power Supply is selected, bring in (Min 1 Max 1) Localized power cord based on the Aruba Wireless Power Cord Table Menu Notes: OCA Display Notes: Most devices are PoE powered from switch so these are optional Accessories Snap-on Covers Rule # Description SKU Aruba AP-615-CVR-20 20-pack White Non-glossy Snap-on Covers for AP-615 R7J56A Notes: Kit contains covers for 20 access points Configuration Rules Rule # Description Notes: OCA Display Notes: Kit contains 20 optional snap-on covers Other Accessories Rule # Description SKU Aruba AP-CBL-EXT10 10-pack CAT6A Ethernet Extension Cables R8L34A 10-pack Extension Cables AP-CBL-SERU Micro-USB TTL3.3V to USB2.0 AP Console Adapter Cable JY728A Drivers available on the Aruba Support Center AP-MOD-SERU Micro-USB TTL3.3V to RJ45 RS232 AP Console Adapter Module R6Q99A Aruba AP-USB-ZB External USB based Dongle with Zigbee and BLE for AP R2X45A Single USB dongle Aruba AP-USB-ZB 10-pk External USB based Dongle with Zigbee and BLE for AP R2Y09A 10-pack USB dongle Aruba AP-USB-ZB 50-pk External USB based Dongle with Zigbee and BLE for AP R2Y10A 50-pack USB dongle Aruba USB LTE Modem for use with Access Points and Gateways R8F34A Aruba USB Extender Cable Kit for use with Aruba USB LTE Modem R8G76A Optional extender cable kit for USB LTE Modem Technical Specifications Hardware Variants AP-615: Internal antenna models Wi-Fi Radio Specifications AP type: Indoor, tri-radio, 2.4GHz, 5GHz and 6GHz (dual concurrent) 802.11ax 2x2 MIMO 2.4GHz radio: Two spatial stream Single User (SU) MIMO for up to 574Mbps wireless data rate with 2SS HE40 802.11ax client devices (287Mbps for HE20) 5GHz radio: Two spatial stream Single User (SU) MIMO for up to 1.2Gbps wireless data rate with 2SS HE80 802.11ax client devices 6GHz radio: Two spatial stream Single User (SU) MIMO for up to 2.4Gbps wireless data rate with 2SS HE160 802.11ax client devices Up to 512 associated client devices per radio, and up to 16 BSSIDs per radio (limited to 4 for the 6GHz radio) Supported frequency bands (country-specific restrictions apply)3: - 2.400 to 2.4835GHz ISM - 5.150 to 5.250GHz U-NII-1 - 5.250 to 5.350GHz U-NII-2A - 5.470 to 5.725GHz U-NII-2C - 5.725 to 5.850GHz U-NII-3 ISM - 5.850 to 5.895GHz U-NII-4 - 5.925 to 6.425GHz U-NII-5 - 6.425 to 6.525GHz U-NII-6 - 6.525 to 6.875GHz U-NII-7 - 6.875 to 7.125GHz U-NII-8 Notes: 3When configured for concurrent operation in 5GHz and 6GHz (only), the U-NII-5 band will be disabled. Available bands and channels: Dependent on configured regulatory domain (country) Dynamic frequency selection (DFS) optimizes the use of available RF spectrum in the 5GHz band Supported radio technologies: 802.11b: Direct-sequence spread-spectrum (DSSS) - 802.11a g n ac: Orthogonal frequency-division multiplexing (OFDM) - 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 8 resource units Supported modulation types: - 802.11b: BPSK, QPSK, CCK - 802.11a g n: BPSK, QPSK, 16-QAM, 64-QAM and 256- QAM (proprietary extension) - 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM (proprietary extension) - 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM and 1024-QAM 802.11n high-throughput (HT) support: HT20 40 802.11ac very high throughput (VHT) support: VHT20 40 80 802.11ax high efficiency (HE) support: HE20 40 80 160 Supported data rates (Mbps): - 802.11b: 1, 2, 5.5, 11 - 802.11a g: 6, 9, 12, 18, 24, 36, 48, 54 - 802.11n: 6.5 to 300 (MCS0 to MCS15, HT20 to HT40), 400 with 256-QAM (proprietary extension) - 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2, VHT20 to VHT80); 1,083 with 1024-QAM (MCS10 and MCS11, proprietary extension) - 802.11ax (2.4GHz): 3.6 to 574 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE40) - 802.11ax (5GHz): 3.6 to 1,201 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE80) - 802.11ax (6GHz): 3.6 to 2,402 (MCS0 to MCS11, NSS = 1 to 2, HE20 to HE160) 802.11n ac packet aggregation: A-MPDU, A-MSDU Transmit power: Configurable in increments of 0.5 dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): Per radio band (2.4GHz 5GHz 6GHz): +21 dBm (18dBm per chain) Notes: Conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain. Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks Maximum ratio combining (MRC) for improved receiver performance Cyclic delay shift diversity (CDD CSD) for improved downlink RF performance Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased signal reliability and range 802.11ax Target Wait Time (TWT) to support low-power client devices 802.11mc Fine Timing Measurement (FTM) for precision distance ranging Wi-Fi Antennas AP-615: Integrated downtilt omni-directional antennas for 2x2 MIMO with peak antenna gain of 2.8dBi in 2.4GHz, 4.5dBi in 5GHz and 4.5dBi in 6GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 to 40 degrees. - Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the combined, average pattern is 2.0dBi in 2.4GHz, 3.5dBi in 5GHz and 3.4dBi in 6GHz. Other Interfaces and Features E0: Ethernet wired network ports (RJ-45) Auto-sensing link speed (100 1000 2500BASE-T) and MDI MDX - 2.5Gbps speed complies with NBase-T and 802.3bz specifications - POE-PD: 48Vdc (nominal) 802.3af at POE (class 3 or higher) - 802.3az Energy Efficient Ethernet (EEE) DC power interface: 12Vdc (nominal, + - 5%), accepts 2.1mm 5.5mm center-positive circular plug with 9.5mm length USB 2.0 host interface (Type A connector) - Capable of sourcing up to 1A 5W to an attached device Bluetooth Low Energy (BLE5.0) and Zigbee (802.15.4) radio - BLE: up to 5dBm transmit power (class 1) and -100dBm receive sensitivity (125kbps) - Zigbee: up to 5dBm transmit power and -97dBm receive sensitivity (250kbps) - Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 2.6dBi GNSS L1 (1575.42MHz) receiver supporting GPS, Galileo, GLONASS and BeiDou signals - Receive sensitivity: -162dBm (tracking) - Integrated omnidirectional antenna with roughly 30 to 40 degrees downtilt and peak gain of 2.3dBi Advanced IOT Coexistence (AIC) allows concurrent operation of multiple radios in the 2.4GHz band Built-in Trusted Platform Module (TPM) for enhanced security and anti-counterfeiting Visual indicators (four multi-color LEDs): for System (1x) and Radio (3x) status Reset button: factory reset, LED mode control (normal off) Serial console interface (proprietary, micro-B USB physical jack) Kensington security slot Automatic thermal shutdown and recovery function Power Sources and Power Consumption The AP supports direct DC power and Power over Ethernet (POE) on port E0 When both DC and POE power sources are available, DC power takes priority over POE Power sources are sold separately; see the 610 Series Ordering Guide for details When powered by DC or 802.3at (class 4) POE, the AP will operate without restrictions. When powered by 802.3af (class 3) POE with the IPM feature disabled, the AP will disable the USB port. With IPM enabled, the AP will start up in unrestricted mode but may dynamically apply restrictions depending on the available power budget and actual consumption. The feature restrictions and order in which these get applied are configurable. Maximum (worst-case) power consumption (without with a USB device attached): - DC powered: 12.5W 18.2W. - POE powered: 14.7W 20.9W. - This assumes that up to 5W is supplied to the attached USB device. Maximum (worst-case) power consumption in idle mode:5.6W 11.0W (DC) or 6.9W 12.9W (POE). Maximum (worst-case) power consumption in deep-sleep mode: 1.0W (DC) or 1.8W (POE). POE Source Class 4 (802.3at) Class 3 (802.3af) Power budget 25.5W 13.9W Power mode Unrestricted Restricted USB port Enabled Disabled Ethernet Enabled Enabled MIMO 2x2 2x2 Max RF power reduction 0dB 0dB POE operating modes and default restrictions with IPM disabled Mounting Details A mounting bracket has been pre-installed on the back of the AP. This bracket is used to secure the AP to any of the mount kits (sold separately); see the 610 Series Ordering Guide for details. Mechanical Specifications Dimensions weight (AP-615; unit without mount bracket): - 160mm (W) x 160mm (D) x 39mm (H) - 520g Dimensions weight (AP-615; shipping): - 212mm (W) x 194mm (D) x 66mm (H) - 800g Environmental Specifications Operating conditions - Temperature: 0C to +50C +32F to +122F - Relative humidity: 5% to 95% - ETS 300 019 class 3.2 environments - AP is plenum rated for use in air-handling spaces Storage conditions - Temperature: -25C to +55C +13F to +131F - Relative humidity: 10% to 100% - ETS 300 019 class 1.2 environments Transportation conditions - Temperature: -40C to +70C -40F to +158F - Relative humidity: up to 95% - ETS 300 019 class 2.3 environments Reliability Mean Time Between Failure (MTBF): 540khrs (62yrs) at +25C operating temperature. Regulatory Compliance FCC ISED CE Marked RED Directive 2014 53 EU EMC Directive 2014 30 EU Low Voltage Directive 2014 35 EU UL IEC EN 60950 IEC EN 62368-1 EN 60601-1-1, EN60601-1-2 For more country-specific regulatory information and approvals, please see your Aruba representative. Regulatory Model Numbers AP-615 (all models): APIN0615 Certifications UL2043 plenum rating - Wi-Fi Alliance (WFA): Wi-Fi CERTIFIED a, b, g, n, ac - Wi-Fi CERTIFIED 6E (ax, 6GHz) - WPA, WPA2 and WPA3 - Enterprise with CNSA option, Personal (SAE), Enhanced Open (OWE) - WMM, WMM-PS, Wi-Fi Vantage, W-Fi Agile Multiband - Passpoint (release 2) Bluetooth SIG Zigbee Alliance Ethernet Alliance (POE, PD device, class 4) Warranty Aruba's hardware limited lifetime warranty Minimum Operating System Software Versions ArubaOS and Aruba InstantOS 8.11.0.0 RF Performance Table Band, Rate Maximum Transmit Power (dBm) per Transmit Chain Receiver Sensitivity (dBm) per Receive Chain 2.4GHz, 802.11b 1Mbps 18.0 -95.0 11Mbps 18.0 -87.0 2.4GHz, 802.11g 6Mbps 18.0 -93.0 54Mbps 18.0 -75.0 2.4GHz, 802.11n HT20 MCS0 18.0 -93.0 MCS7 16.0 -74.0 2.4GHz, 802.11ax HE20 MCS0 18.0 -93.0 MCS11 13.0 -62.0 5GHz, 802.11a 6Mbps 18.0 -93.0 54Mbps 16.0 -75.0 5GHz, 802.11n HT20 HT40 MCS0 18.0 18.0 -92.0 -89.0 MCS7 16.0 16.0 -73.0 -70.0 5GHz, 802.11ac VHT20 VHT40 VHT80 MCS0 18.0 18.0 18.0 -92.0 -89.0 -86.0 MCS9 15.0 15.0 15.0 -67.0 -64.0 -61.0 5GHz, 802.11ax HE20 HE40 HE80 MCS0 18.0 18.0 18.0 -91.0 -89.0 -86.0 MCS11 13.0 13.0 13.0 -62.0 -59.0 -56.0 6GHz, 802.11ax HE20 HE40 HE80 HE160 MCS0 18.0 18.0 18.0 18.0 -91.0 -88.0 -85.0 -82.0 MCS11 13.0 13.0 13.0 13.0 -62.0 -59.0 -56.0 -53.0

HPE Networking Instant On Access Point Dual Radio 2x2 Wi-Fi 6 (RW) AP21 (S1T09A) What's new · Wi-Fi CERTIFIED 6™ support for up to 50 user devices. Designed to provide better speed and coverage for smaller spaces. PoE or DC powered to expand your network. Use with any other Instant On access points to create a Smart Mesh to extend your network without additional ethernet cables Best when used in conference rooms, home offices, or low-density environments. Overview The HPE Networking Instant On Access Point AP21 is a dual radio indoor access point designed to bring connectivity to small spaces. This Wi-Fi CERTIFIED™ 6 access point offers modern WI-Fi standards in a small footprint to enhance the connectivity of your network for up to 50 devices. The dual-band radios offer suitable range for a 1500 sq ft space at an affordable price with the same features as other more costly access points. The HPE Networking Instant On AP21 can also be used with Smart Mesh with any other Instant On access point to extend your network coverage without needing to run new cables—HPE Networking Instant On AP21, small yet mighty coverage for your growing wireless needs. Features 802.11ax Wi-Fi Certified 6 The HPE Networking Instant On Access Point AP21 features Orthogonal Frequency-Division Multiple Access (OFDMA) which allows them to handle multiple Wi-Fi 6 capable clients on each channel simultaneously; this improves efficiency by boosting overall capacity and reducing latency. Target Wake Time (TWT) – Ideal for IoT devices that communicate infrequently, TWT establishes a schedule for when clients need to communicate with an AP. This reduces power consumption and can extend the battery life of clients. Multiple Input, Multiple Output (MIMO) – Allows the access point to serve multiple clients (Wi-Fi 5 and Wi-Fi 6) simultaneously. Safeguard Your Network With WPA-Enterprise Features HPE Networking Instant On Access Points AP21 come with top-level security features, always on, out of the box, such as WPA2 WPA3 and Enhanced Open support for protecting your wireless network. Use the HPE Networking Instant On mobile app or web portal to see where clients on your network are going with the application's insight. Block certain types of traffic in the mobile app or web portal to keep your network safe and employees productive. Create a Custom Guest Access Experience HPE Networking Instant On Access Point AP21 is ideal for single-site businesses or homes like cafe’s, restaurants, or office buildings. The easy-to-use captive portal, free to set up in the HPE Networking Instant On app or web portal, creates an easy onboarding process for employees or guests. Integrate with 3rd party analytics partners like Skyfii, Aislelabs, and Wavespot to gain customer insights while they are on your network. Technical specifications Name HPE Networking Instant On Access Point Dual Radio 2x2 Wi-Fi 6 (RW) AP21Product number S1T09A Differentiator HPE Networking Instant On Access Point AP21 is for businesses that have invested in PoE infrastructure throughout their facility, as these SKUs will ship without a PSU. Certifications Wi-Fi Certified 6 Input voltage PoE: 802.3at (class 4) or 802.3af (class 3) DC power (12V) Wi-Fi antenna Dual Omnidirectional 2x2 MIMO Connectivity, standard Wi-Fi 11ax Ports 1 GbE BaseT Uplink DC Power Connector LED status Indicators Reset LED control button Kensington security slotMounting Ceiling Wall mount clip Power consumption 10.9W (DC) Radio coverage Dual-Band 802.11ax 2x2 5Ghz 2.4Ghz MIMO Warranty HPE Networking Instant On 2-Year

Aruba Instant On AP22 (RW) Access Point. The Aruba Instant On AP22 provides high-performance concurrent 2.4 GHz and 5 GHz Wi-Fi 6 (802.11ax) features with MIMO radio (2 x 2 at 2.4 GHz, 2 x 2 at 5 GHz) while supporting older 802.11a b g n ac wireless services.Záleží vám na tom, abyste byli vybaveni spolehlivým bezdrátovým připojením? WiFi access point HPE zaručuje rychlý přístup na internet pro každé jednotlivé zařízení. Prodlužuje signál WiFi, proto neztrácíte spojení při přechodu mezi místnostmi. Díky dvěma frekvenčním pásmům (2,4 a 5 GHz) je možné na jedno z nich připojit smart home zařízení a na druhé pak běžná zařízení jako smartphony, notebooky apod. Přístupový bod je určen do kanceláří, domácností nebo škol, kde posílí bezdrátovou konektivitu. Skrze WiFi umí přenášet 1774 Mb s, a tak máte jistotu, že vaše připojení bude dostatečně rychlé. K podporovaným standardům patří 802.11a, 802.11b, 802.11g, 802.11n, 802.11ac a 802.11ax, podporuje tedy generaci WiFi 6. Bezpečnost přenášených dat má na starost šifrování WPA2 a WPA3. Přístupový bod HPE umožňuje propojení s digitálním světem. Vybavení zajišťující spolehlivé připojení bezdrátového přístupového bodu Vnitřní WiFi access point HPE slouží pro optimální rozšíření vaší síťové infrastruktury. Jeho konstrukce zahrnuje možnost připojení pomocí LAN. Nabízí zisk antény až 5,6 dBi. Nabízí pokročilé funkce, které jistě oceníte. Podporuje PoE napájení, to znamená, že jej lze připojit do síťového rozvodu pomocí jednoho kabelu. Jedná se o PoE standard 802.3af (PoE). Zásluhou technologie MU-MIMO bude možné k přístupovému bodu připojit více koncových zařízení. Správa zařízení skrze internetové rozhraní je možná díky funkci přístup přes Cloud. Wi-Fi Mesh systém umožňuje vytvoření vysoce efektivní a flexibilní sítě, což zajistí spolehlivou a konzistentní dostupnost signálu v celém areálu. Jeho předností je, že poskytuje bezproblémové fungování v síti používající protokol IPv6. U access pointu není opomenuta ani funkce Firewall, pomocí které je síť zabezpečena prostřednictvím monitorování a regulace přístupových práv, což brání neoprávněnému přístupu nebo útokům zvenčí. Na tomto zařízení je možné vytvořit 8 WiFi sítí. Obsahem balení je rovněž ethernetový kabel a držák pro uchycení. Klíčové přednosti access pointu Aruba Instant On AP22 Access Point Bezdrátový přístupový bod HPE zaručuje rychlý přístup na internet pro každé jednotlivé zařízení Prodlužuje WiFi signál, což zabraňuje ztrátě spojení při pohybu mezi místnostmi Vysílá ve dvou frekvenčních pásmech 2,4 GHz a 5 GHz Bude vhodný do kanceláří, domácností či škol Skrze Wifi umí přenášet 1774 Mb s Mezi standardy pro bezdrátovou komunikaci náleží 802.11a, 802.11b, 802.11g, 802.11n, 802.11ac, 802.11ax a podporuje tedy generaci WiFi 6 Za zabezpečení přenášených dat je zodpovědné šifrování WPA2 a WPA3 Jeho konstrukce zahrnuje rovněž možnost připojení prostřednictvím LAN Celkově obsahuje 2 vnitřní antény Nabízí zisk antény až 5,6 dBi Je zásobován energií skrz PoE (Power over Ethernet) K vylepšení stability a rychlosti přenosu dat poslouží funkce MU-MIMO Přístup přes Cloud umožňuje správu pomocí internetového rozhraní WiFi Mesh zajistí spolehlivou dostupnost signálu v celém areálu Je dostupná plná podpora IPv6 protokolu Vybavení access pointu zahrnuje i funkci Firewall Maximální počet SSID na tomto zařízení je 8 Do balení náleží také ethernetový kabel a držák pro uchycení Rychlost na 5 GHz: 1200 Mb s Konektory LAN: 1× PoE standard: 802.3af (PoE) Rozměry: 16 × 16 × 3,7 cm (hך×v) Hmotnost: 500 g KEY FEATURES: Fast 802.11ax Wi-Fi CERTIFIED 6 (Wi-Fi 6) MU-MIMO performance Support for Smart Mesh Wi-Fi technology Integrated Wi-Fi router gateway Integrated Bluetooth Easy to use web and mobile application for setup and management Secure Wi-Fi for guests with easy setup Technical parameters Dual radio for simultaneous dual band operation 5 GHz 802.11ax 2x2 MIMO for wireless data flow up to 1.2 Gbps, with Multi User MIMO support (Wi-Fi 6) 2.4 GHz 802.11ax 2x2 MIMO for wireless data transfer speeds of up to 574 Mbps (Wi-Fi 6) Uplink Gigabit Ethernet port with PoE-in support (802.3af) DC power connector (12V) Low power Bluetooth radio status indicators (BLE) Reset LED button Kensington security slot Power over Ethernet (POE): 802.3af (Class 3) Maximum power consumption (worst case): 10.1 W (PoE), 8.8 W (DC) DC power supply (12V) Dimensions: 160 mm x 160 mm x 37 mm, excluding mounting accessories Weight: 500 g Aruba Instant On AP22 Indoor Access Points. High-speed Wi-Fi designed with small businesses in mind. Perfect for reimagined offices, schools, and retail hospitality businesses. Small businesses are facing a number of challenges—challenges that need constant attention. The right technology can help you stay on top of them and stay ahead of the curve. Technologies like the ones found inside the AP22. To meet the increasing needs and volumes of connected devices, Aruba Instant On is announcing its first Wi-Fi 6 access point: AP22. Delivering higher capacity and greater performance at a competitive price, the AP22 is the perfect access point for small businesses with expanding mobile, cloud, and IoT requirements. Wi-Fi Certified 6TM AP22 access points deliver faster Wi-Fi speeds, greater capacity, and reduced latency between access points and devices for a superior Wi-Fi experience. With the AP22, you can upgrade your Wi-Fi network to boost performance across devices now, while preparing it for more mobile and IoT devices in the future. Already have a demanding mobile and or IoT environment? Delivering 4x the capacity of 802.11ac access points, AP22 can provide an exceptional user experience in a broad variety of scenarios. Remote offices. Hybrid classrooms. Hotels and restaurants. Reimagined retail and hospitality. The AP22 can handle them all without breaking a sweat. Want to make wires a thing of the past? Combine the AP22 with Smart Mesh Wi-Fi for complete wireless coverage. Want to keep bandwidth hogs and unknown devices off your network? Banish them with the flip of your thumb on the Aruba Instant On App. We know the critical role Wi-Fi plays in business today. No business can’t afford downtime. The Aruba Instant On AP22, at every level, is designed for rapid deployment and simplified management. Be it mounting hardware, or remote device management, or having access to the latest business-grade software, the AP22 lives to make your life easier. Aruba Instant On AP22 Indoor Access Points Key Features Fast 802.11ax, 2X2:2 Wi-Fi CERTIFIED 6TM (Wi-Fi 6) MU-MIMO performance Smart Mesh Wi-Fi support Built-in Wi-Fi router gateway functionality Integrated Bluetooth Easy-to-use web and mobile app for setup and management Secure Guest Wi-Fi with simple setup Application classification, control and visibility Standard Features Orthogonal Frequency-Division Multiple Access (OFDMA) Allows access points (APs) to handle multiple Wi-Fi 6-capable clients on each channel simultaneously—regardless of device or traffic type. This improves efficiency by boosting overall capacity, while reducing latency.. Target Wake Time (TWT) Ideal for IoTs that communicate infrequently, TWT establishes a schedule for when clients need to communicate with an AP. This helps reduce power consumption, extending the battery life of clients. Multiuser, Multiple Input, Multiple Output (MU-MIMO) Allows you to serve multiple clients (Wi-Fi 5 and Wi-Fi 6) at the same time. 1024-Quadrature Amplitude Modulation (1024-QAM) Enables a 25% data increase over 256 QAM, improving throughput in your access points and devices. Trusted Platform Module (TPM) All Aruba Instant On access points have an installed TPM for secure storage of credentials, keys, and boot codes. Basic Service Set Coloring (BSS Coloring) Allows the network to assign a "color" tag to a channel and reduce the threshold for interference. Network performance is improved because APs on the same channel can be closer together and still transmit at the same time—as long as they are different colors. Aruba Advanced Cellular Coexistence (ACC) Uses built-in filtering to automatically minimize the impact of interference from cellular networks, distributed antenna systems (DAS), and commercial small-cell or femtocell equipment. Low Density Parity Check (LDPC) Delivers high-efficiency error correction for increased throughput.. Transmit Beamforming (TxBF) Delivers increased signal reliability and range. The Aruba Instant On App Manage everything through our official app on the device of your choice. Manage your network from anywhere, anytime- all from the palm of your hand. Built-in Security Gateway Firewall Stop unwanted people and bots from accessing your network. Leverage advanced features that do not require external gateways—or the complexity that comes with them. Quickly and easily swap it out with another AP in a single click, in case of gateway failure. Complete App Visibility and Control Get full visibility into the apps running on your network. Block certain applications from being used. Manage this feature straight from the Aruba Instant On app. Tailored User Experiences Customize the experience with logos, authentications, and rules of use. Apply bandwidth rates. Set data usage per app. Limit duration of use. Use an external portal or service like Facebook Wi-Fi. Create open guest networks for quick and easy access. Enterprise Grade Wi-Fi and Features Control network widths, channels, and channel widths to suit your specific environment. Keep users happy as they move between spaces or meetings with a seamless handoff between APs. Just provide secure WPA2 or WPA3 authentication on your networks and we’ll do the rest. Multi-site Management Manage multiple sites, multiple networks, distributed deployments, and multi-tenancy deployments with ease through our cloud-hosted web interface and mobile app. Create unique configurations, statistics, guest portals, and admin read write and read-only privileges for every site. PPPoE and Static IP Every customer has a different environment. They might want to authenticate with the ISP’s PPPoE server and provide static IP to the APs. Smart Mesh Extend coverage to hard-to-reach spaces where Ethernet cabling may not exist. Set up a Mesh network up in minutes through the app—indoors or out. 5-star Voice and Video Quality Keep users connected via softphones and mobile apps. Automatically detect and prioritize voice and video applications such as Skype, FaceTime, and WeChat that use SIP, SCCP and other popular protocols. Technical Specifications WI-FI Radio Specifications Dual radio for simultaneous dual-band operation 5 GHz 802.11ax 2x2 MIMO for up to 1.2 Gbps wireless data rate, with Multi User MIMO support (Wi-Fi 6) 2.4 GHz 802.11ax 2x2 MIMO for up to 574 Mbps wireless data rate (Wi-Fi 6) Maximum (aggregated, conducted total) transmit power (limited by local regulatory requirements): ­ 5GHz band: +21dBm (+18dBm per chain, 3dB MIMO gain) ­ 2.4Ghz band: +21dBm (+18dBm per chain, 3dB MIMO gain) Power Power over Ethernet (POE): 802.3af (class 3) Max power consumption (worst-case): 10.1W (PoE), 8.8W (DC) DC power (12V) Notes: Power sources are sold separately unless you purchase the bundle SKU which comes with power options. Additional interfaces Uplink Gigabit Ethernet port, with PoE-in support (802.3af) DC power connector (12V) Bluetooth Low Energy (BLE) radio LED status indicators (2) Reset LED control button Kensington security slot Antennas Down-tilt omni-directional antennas for 2x2 MIMO with peak antenna gain of 4.3dBi in 2.4GHz and 5.6dBi in 5GHz (of the effective, combined pattern for both antennas in each band). Mounting The access point ships with a white mount clip that can attach to both wall and ceiling. You can also purchase a mount (R6P90A) for aesthetic design and looks of the APs, to blend seamless into your environment. Mounting The access point ships with a white mount clip that can attach to both wall and ceiling. You can also purchase a mount (R6P90A) for aesthetic design and looks of the APs, to blend seamless into your environment. Dimensions and weight Dimensions and weights exclude mount 160 (W) x 160 (D) x 37 mm (H) 6.3 (W) x 6.3 (D) x 1.5 in (H) 500 gm 1.1 lbs Environmental Operating temperature: 0° C to +40° C (32° F to +104° F) Certifications UL 2043 plenum rating EN 60601-1-1 and EN 60601-1-2 (for deployment in medical environments) Wi-Fi Alliance certified (WFA) 802.11ax with (Wi-Fi 6), WPA2, WPA3 Warranty & Support Aruba Instant On 2-Year warranty with 24x7 phone support for first 90 days and chat support for the entire warranty period. Community support as long as you own the products. Should you require longer support, please purchase a Foundation Care contract for your APs. The SKUs are HK1Y0E (3 years) and H30GZE (5 years).

Aruba Instant On AP25 Flush Mount Sleeve